640-816 exam questions

This braindumps needs pre order, and we will make this product for you within 2~3 weeks.

640-816 Exam Description

It is well known that latest 640-816 exam test is the hot exam of Cisco certification. Exam4Dumps.info offer you all the Q&A of the 640-816 real test . It is the examination of the perfect combination and it will help you pass 640-816 exam at the first time!

　
　
Exam : CISCO 640-816
Title : Interconnecting Cisco Networking Devices Part 2


1. Refer to the exhibit.
A junior network engineer has prepared the exhibited configuration file. What two statements are true of the planned configuration for interface fa0/1? (Choose two.)
A. The two FastEthernet interfaces will require NAT configured on two outside serial interfaces.
B. Address translation on fa0/1 is not required for DMZ Devices to access the Internet.
C. The fa0/1 IP address overlaps with the space used by s0/0.
D. The fa0/1 IP address is invalid for the IP subnet on which it resides.
E. Internet hosts may not initiate connections to DMZ Devices through the configuration that is shown.
Answer: BE

2. Refer to the exhibit. The router has been configured with these commands:
hostname Gateway
interface FastEthernet 0/0
ip address 198.133.219.14 255.255.255.248
no shutdown
interface FastEthernet 0/1
ip address 192.168.10.254 255.255.255.0
no shutdown
interface Serial 0/0
ip address 64.100.0.2 255.255.255.252
no shutdown
ip route 0.0.0.0 0.0.0.0 64.100.0.1
What are the two results of this configuration? (Choose two.)
A. The default route should have a next hop address of 64.100.0.3.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers.
D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet without address translation.
Answer: DE

3. Refer to the exhibit. Two routers have just been configured by a new technician. All interfaces are up. However, the routers are not sharing their routing tables. What is the problem?
A. Split horizon is preventing Router2 from receiving routing information from Router1.
B. Router1 is configured for RIP version 2, and Router2 is configured for RIP version 1.
C. Router1 has an ACL that is blocking RIP version 2.
D. There is a physical connectivity problem between Router1 and Router2.
E. Router1 is using authentication and Router2 is not.
Answer: B

4. Refer to the exhibit. Which statement describes DLCI 17?
A. DLCI 17 describes the ISDN circuit between R2 and R3.
B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
Answer: C

5. What is the default Local Management Interface frame type transmitted by a Cisco router on a Frame Relay circuit?
A. Q933a
B. B8ZS
C. IETF
D. Cisco
E. ANSI
Answer: D

6. Refer to the exhibit. The network shown in the exhibit has just been installed. Host B can access the Internet, but it is unable to ping host C. What is the problem with this configuration?
A. Host B should be in VLAN 13.
B. The address of host C is incorrect.
C. The gateway for host B is in a different subnet than the host is on.
D. The switch port that sends VLAN 13 frames from the switch to the router is shut down.
E. The switch port connected to the router is incorrectly configured as an access port.
Answer: B